Tamarack Technologies HV1600-GDR

The HV-1600-GDR offers maximum insulation value with an R-38 rating. Recommended for areas where it is very cold during the winter, offers R-38 insulation to the home.

Benefits:

• R-38 Insulation - air tight seal between attic and living area when not in use
• Easy installation - designed to fit between 14" & 24" on center studs
• Two speeds operation - 1600 cfm high / 1150 cfm low
• Hard wire to switches option included
• Radio Frequency (RF) remote control
• Save from 15-55% off summer utility bills
• 115 VAC 60 Hz
• Made in the USA
• UL Listed
• Download the HV-1600 Installation Instructions

The HV series of whole house fans are insulated and when not in use form an air tight seal between your attic and living space. There is no other unit available that boasts these levels of insulation and protection. Fan housing is now black as shown in main product picture.

As an additional quality control method, every single unit is tested and run at the factory for 24 hours prior to shipping, a commitment to excellence. 

HV1600 2 Speed Specification Sheet - Click Here To View

Grille: The HV system includes a 24" x 14" white return air grille. The outside diameter of the grille measures 25 3/4" x 15 3/4". The rough opening of the grille measures 23 1/4" x 13 7/8".

Controls: The HV1600 2 Speed comes standard with RF remote controls, which has a range of approximately 30'.

Wiring The HV1600-GDR:

As of 12/2005 - All HV1600 fans have a line cord for ease of installation. Simply plug it in and the fan will work with the included handheld remote control. The dedicated remote control system offers the user a simplified 110 volt powered remote control. The system includes a hand-held transmitter, which operates on a 12-volt battery (included), a receiver which has been built into the fan. The transmitter features a signal operating light that goes on when the ON or OFF buttons are depressed. The controls offer 256 unique security codes that are factory programmed into the system allowing multiple remote control units in the same room or building. The systems operating distance is 30' and is not restricted to "line-of-sight" applications because the system uses radio frequency control. It operates on the R.F. frequency of 303.875 MHz. The control is UL listed and is FCC certified in the U.S. and I.S.C. certified in Canada.

Important Facts To Consider When Sizing A Whole House Fan:

If you have done any research on whole house fans you will see a lot of sites that recommend multiplying your homes total square footage by three and that will tell you what size whole house fan you would need in air flow (CFM). Yes, that formula will work, but it is very inefficient and many times impractical. In the case of whole house ventilation for cooling purposes, bigger is not necessarily better.

In order for the whole house fan to operate efficiently and effectively, consider the below variables:

1. Fan size
3. Intake air source
4. Attic exhaust vent requirements
5. Climate differentials and peak summertime temperatures

Fan Size:

The bigger the fan the faster it will cool your home?  Not necessarily. After the first few air exchanges, the value of having a large air flow is diminished.  Yes, the air flowing into your home will be cooler, but your house will not. A home that has been in a hot environment throughout the day actually stores and retains heat. The effects of the heat permeates throughout the entire home, especially in the attic. Cooling the home is best accomplished by having a constant and continuous flow of cooler air over a longer period of time, to effectively dissipate the stored heat. A lower flow of cool air is very effective at removing the stored heat in your home.

Intake Air Source & Exhaust Requirements:

In order for cooler outside air to enter the home you must open a minimum amount of windows or doors to allow the cooler air to flow into your home. On the same note and this is very important, you must have an adequate amount of exhaust vents to allow the air pulled into your home to exhaust the warm air outside. A good rule of thumb to use is for every 1000 cfm of airflow, you need 1.3 square feet of unobstructed roof venting or 1.33 sq. ft. of net free venting.

Net Free Area Defined: For every 750 cfm of airflow, it is recommended that there be a minimum of 1.33 sq. ft. of attic venting, i.e. roof vents, gable vents, soffit vents, ridge vent. This will allow the air flow of the fan's exhaust air into